High Air Pressure Black SRC547 RC Drill Bit For Mineral Exploration Drilling
Product Introduce:
RC hammers and bits are used in hole drilling in mines, hydrology and water well, geothermal well, geothermal air conditioning well, geologic exploration, complicated gravel stratum, etc
Especial suitable for complicated formation (Formation loose, difficult to drilling and unstable of hole wall), exhausting for deep hole, environment protection.
Specification:
SRC547 series drill bit specification
| Drill bit shank | Bit diameter (mm) | Guage | Front | Center | Recommend shroud | weight (kg) |
| buttons | buttons | buttons |
| SRC547 | 136 | 8×φ16 | 6×φ16 | 3×φ14 | 134 | 14.2 |
| 140 | 8×φ16 | 6×φ16 | 3×φ14 | 138 | 14.5 |
| 143 | 8×φ16 | 6×φ16 | 3×φ14 | 141 | 14.7 |
| 146 | 8×φ16 | 6×φ16 | 3×φ14 | 144 | 15 |
SRC547 Hammer specification
Shank
| Length | Weight | External diameter | Bit hole range | Connect thread | Working pressure | Impact rate at 2.4Mpa | Recommend rotation speed |
SRC547
| 1270mm | 74kgs | 124.5mm | 130-146mm | 4.5" Remet
/Metzke | 1.5-3.5Mpa | 35Hz | 25-40rpm |
Adavantages:
1.Reverse Circulation bit is well known for its high wear resistance on medium-hard to hard abrasive rock formations .Featuring spherical tungsten carbide inserts that is known to have strong configuration against carbide fracture.
2.Recommended for eliminating hole deviation
3.Widely used drifting and tunneling
4.Bit face design is ideal for medium-hard to hard abrasive rock
Basics of Reverse Circulation Drilling:
(1) RC drilling uses rods with inner and outer tubes, the drill cuttings are returned to surface inside the rods. The drilling mechanism is a pneumatic reciprocating piston known as a hammer driving a tungsten-steel drill bit.
(2) RC drilling utilizes much larger rigs and machinery and depths of up to 500 meters are routinely achieved. RC drilling ideally produces dry rock chips, as large air compressors dry the rock out ahead of the advancing drill bit.
(3) RC drilling is slower and costlier but achieves better penetration than RAB or air core drilling; it is cheaper than diamond coring and is thus preferred for most mineral exploration work.
(4) Reverse circulation is achieved by blowing air down the annulus of the rod, the differential pressure creating air lift of the water and cuttings up the inner tube which is inside each rod. It reaches the deflector box at the top of the drill string then moves through a sample hose which is attached to the top of the cyclone.
The drill cuttings travel around the inside of the cyclone until they fall through an opening at the bottom and are collected in a sample bag. For any drill hole there will be a large number of sample bags, each one marked to record the location and drilling depth that the sample was obtained.
The collected series of sample bag cuttings are later taken for analysis to determine the mineral composition of the drill hole. The analysis results of each individual bag represents the mineral composition at a particular sample point in the drill hole. Geologists can then survey the drilled ground analysis and make decisions about the value of the overall mineral deposit.
Photo:
About us:
SOLLROC Reverse Circulation drilling (RC) ,from size 3’’ to 5.5’’, is a technique of drilling that uses dual wall drill rods that consist of an outer drill rod with an inner tube. By using compressed air to extract rock fragments sample,the samples travel through rods to a sample splitter at surface, avoiding all contact between the samples and the borehole wall that allows samples to be retrieved with minimal contamination,which is mainly used in deep hole exploration and mining grade control.
Delivery Way:
By Air, By express or By Sea
Package :
Ply-wooden cases + pallet
Product Tags:
|
|
High Air Pressure SRC547 RC Drill Bit For Mineral Exploration Drilling Images
|
